Robimo doors for shafi coupe samostyino

22.09.2021

The coupe-compartment is handy, the flakes of the doors at the open station do not take a lot of trouble. Yogo vzagalі can be built uncorporated - from nіshі, from the wall to the wall. All in all, it’s in a vypad to know - to raise the doors for the shafi-compartment, and then pick up the zapovnennya (or navpaki, it’s not so important).

Talk about zhorstki obmezhennya behind the size of the doors for the shafi-compartment, oh no. Zrobiti can be-yakі behind the same width. Ale є parameters, which are highly recommended, are given on the basis of the information provided by the operation:

Chair design

Shafi-compartment doors are stored from profiles:

All tse maє takiy viglyad, yak in the photo. The frame is inserted into the groove for vibration of the material for the doors. Tse can be a sklo, mirror and other materials.

Rozdilny profiles є obov'yazkovy. The stench is needed, as you pick up chairs from other materials, or the stench in such a view is more befitting of you. The maximum material thickness is 10 mm, the minimum is 4 mm. Big thin - sklo, plastic, mirror - inserted through the gasket.

The stool is too small to collapse, rollers are installed on it - up the mountains below. On the lower rollers, the entire mass of doors falls, and the upper rollers stabilize the position of the canvas vertically, not giving them visibility.

The rollers are fastened to the child's profiles for additional special elements of the fastening.

Straight for compartment doors

Yak vi rosumite, stool - not everything. It is necessary to directly collapse the doors themselves. Їх dvі - upper and lower. The stench is meaningful to the sight.

When installing the doors, it is a good idea to put the stool at the top straight, push the chair all the way down and put the bottom rollers at the bottom. The design is shown in the offensive photo.

Rozrakhunok rozmіriv

With self-folding doors for the shafi compartment, there are two options. The first one is to change the openings, think over the doors, you want your mother and from the information to turn up to the doors from the prepared doors. Just perekonayte, how the stink of selling accessories without paying for folding. The manager himself will help you with the necessary materials, see the size and sound the bag. It's simple. But if you happen to buy everything from the same office, tobto. vibrate from that.

Chairs

Protect the width of the chairs so that only one handle is visible at the closed camp of the ball, but when you close the door itself, the canvas is not to blame. For compartment doors with two chairs, fit in like this: adjust the width of the opening, add the width to the profile and extend it. It will be the width of the chair.

Napril, holes 1600 mm, width of the profile-handle 26 mm. We accept mo 1600 mm + 23 mm / 2 = 811.5 mm. Beast to respect, the width of the profile-handle is taken pretty well. Vona can be of a pink shape, naturally, wide. Give the width of the design you want to design for an hour.

For a razrahunku tristulkova need, add the width of the profile and the size to 3.

Stock: hole 2100 mm, width of the handle itself - 26 mm. Vvazhaєmo: 2100 mm + 2 * 26 mm / 3 = 717 mm.

Everything is simpler with the hanging. From the height of the shafi, the height is 40-45 mm, and the height of the stool can be taken off, as well as to make some noise, as well as for the dinner of the children. With the size of the chairs, that's all.

Zapovnennya

So it’s like it’s in the frame of the profiles, because of the width of the chair, it’s taken away from the width of the profile. Those same prophesied with the height - the visota of the lower and upper profile.

Already, the width of our chair is 811.5 mm. The width of the handle's profile is 18 mm. So, like a handle, put from two sides, a number underneath. We can accept 36 mm. At the same time, the width of the filling is 811.5 mm - 36 mm = 775.5 mm.

The height of the vazhaєmo is the same: the width of the upper profile is 12 mm, the width of the lower one is 48 mm. At the same time, the height of the zapovnennya is 2350 mm - 12 mm - 48 mm = 2290 mm. The whole and the price of laminated chipboard is not required, but does not require a power supply. Yakscho stool is a complete mirror or a slope, because of the knowledge of the demand, you must see it as a gumi. Vona become 1 mm, ale shards fit around the perimeter, to zagalny-zgory і from the bottom-edge 2 mm. At the same height, the height of the zapovnennya is 2290 mm - 2 mm = 2288 mm.

As soon as the stools are stored in fragments, it is also seen in the back of the profile. The won should also be approx. 1 mm.

Profiles

The height of the vertical profiles of the frame of the door hanging chair. The width of all the horizontal ones is calculated in lieu of the width of the handle: from the width of the chair to the bottom of the width of the handle (їх dvі).

Come on, handle width 26 mm. Acceptable width of vertical profiles: 811.5 mm - 26 mm * 2 = 759.2 mm.

Photo call about folding

A selection of all profiles is drawn exactly according to the rozrahovaniye sizes. Accuracy is perfect. Різ - strictly perpendicular, pіd 90 °. At the profile-handles, drill open for the installation of rollers and fasteners.

Open two diameters. The exact size should be taken from the dimensions of the purchased mounting, but in the main size there are two: 4 mm and 6 mm, as well as 6 mm and 10 mm.

Allow one such aperture to flap, the center of which is located at the end of 7 mm towards the edge of the profile, at the bottom there are two openings - the first at the end of 7 mm towards the edge, the other - coming out of the profile of 42 mm.

When folded, all parts of the reserve are picked up beforehand. Sphatku, like є slope or mirror, along the perimeter will be gummed up. Vaughn just finger pressure on the end of the details. Along the edges of the gorge, it looks, it pushes it in, ale without nahil on the offensive bik.

On the mirror from the rear side, glue the adhesive strip. You can vikoristovuvati zvychaynu self-adhesive. Tsya plivka does not let the ulamams rozsipatsya, as the mirror rosib'yatsya.

The chair is folded, її is selected for additional profiles. Parts napovnennya are simply inserted from the zusilli to the profile. Inodi can be known as a Zusill. You can knock on the end with the til side of the valley or vikoristovuvati gum mallet.

Just insert the parts into the grooves of the profile and tap on the butt

If the chair is selected, following the same principle, the top and bottom are set up as a profile.

Then it is time for the installation of professional handles. Everything is the same: turn it into a groove, stitch, and it went all the way along all the way without distortions. If the frame is selected, it is necessary to tighten the brackets. Fix it from the top. Take the holder, insert it into the holes before the holes. They saw exactly how they saw it, the gwent was tapped at the groove of the upper cross section.

It is tightened with a hex key. Without slightly tightening it all the way, between the head of the screw and the crossbar of the profile, insert the upper rollers, then until the gwent.

The same operation is repeated from the side. Then we go down. Here the mount will be installed at the upper openings. It's just tightening all the way. Similarly, repeatable from the side.

Installation of the lower roller - the plate is started at the profile

The spring is pidtiskaєmo, filling the roller housing in the middle. Insert a screw into the hole, magayuchis eat it in the nest, tighten it with a hexagon. Win can know the smallest size - three less, lower іnshі - that is why the gwent is the thinnest and the one who has died.

It is not necessary to tighten it all the way. So, you have a plate at a centimeter or so. When installing the doors, it’s possible to adjust the position of the stool with the help of the screw to adjust the position of the chair - it’s going to go down or go down.

Stir tightly onto the roller wheel, turn into the body, then turn by the spring spring opening. The whole simple mechanism will ensure the smoothness of the doors for the compartment of the shafi.

Having taken all the chairs, it is possible to switch to the installation of the direct ones. The stench of guilt roztashovuvatya strictly one go one, navigate without seeing the milimeter. Vikoristovyte temple or laser rіven ().

Fasten the top with a strap. Vona krypitsya either to the stele or to the upper part of the Shafi. From the police station - not less than 100 mm;

At the bottom, the springs are inserted into the groove from the sides at the groove. The stench is surrounded by doors. A number of springs are available for a number of chairs, and the stench from both ends will rise.

I do not have a laser beam, I don’t have to worry about the grab, for the cob I can just lay the bottom straight, as long as it’s not closed. Then stand up one blade by hooking the top rollers of the ember, and pushing the bottom into the required groove. This is the order of the door to ring the upper and lower strains.

Having turned the canvas vertically, you will automatically turn the bottom straight. Її to get rid of it, screw it up. Just respectfully quit, don't destroy the doors.

Stop, to get lost, - to glue the schlegel from the sides. It’s a pile of smog, so it’s self-adhesive, yak will help you hit the stool on the walls of the shafi (or, just for the sake of it, since the shafa is uncased).